|
Type
|
21CBM concentrated sulfuric acid tanker
|
|
运输介质
Transport medium
|
浓硫酸，1.84吨/立方
Concentrated sulfuric acid, 1.84 tons/cubic meter
|
|
结构类型
Tanker structure
|
小V型，直缝焊制两个偏心直角斜圆锥台环焊对接。
Small V shape, straight seam welded two eccentric right Angle bevel ring butt welding.
|
|
外形尺寸
Dimensions
|
11150X2500X3350（根据牵引车参数调整，保证匹配）
11150X2500X3350 (Adjust according to the parameters of the tractor to ensure the match)
|
|
自 重
Tare weight
|
9600Kgs（Appro约值）
|
|
载 重
Loading
|
38000Kgs（Appro约值）
|
|
轴 距
Wheelbase
|
6700+1310+1310（根据牵引车参数调整，保证匹配）
6700+1310+1310(Adjust according to the parameters of the tractor to ensure the match)
|
|
罐 体 部 分
Tank body
|
|
罐体尺寸
Tank body dimensions
|
按照设计
As design
|
|
有效装载容积
Effective capacity
|
21立方米，另增加约5%气体空间
21CBM， plus ～5% ullage
|
|
封头厚度与材质
Head thickness and material
|
Q345B 名义厚度8mm
Q345B T8
|
|
罐体厚度与材质
Tank body thickness and material
|
Q345B 名义厚度6mm
Q345B T6
|
|
防波板板厚度、材质与结构类型
Baffles typpe
|
8道防浪板，间距不大于1200mm，防波板上下开硫酸口，另开直径700mm人孔。蝶形结构，Q345B 材质，6mm。
Eight baffles, the spacing is not more than 1200mm, the baffles open sulfuric acid holes at the top and bottom, and open another 700mm diameter manholes. Butterfly structure, Q345B material, 6mm.
|
|
罐内是否防腐处理
Whether the tank inside is treated with corrosion protection
|
无
Non
|
|
罐体分仓数
Compartments
|
单仓
Single compartments
|
|
罐体形状
Tank body size
|
浅V型
Small V-shape
|
|
罐体加强圈
Tank inside reinforcement rings
|
10道
10 pcs
|
|
罐 体 上 部 设 施
Tanker Top
|
|
人孔
Manhole
|
六爪不锈钢304人孔盖，耐酸密封件
6-jaw stainless steel 304 manhole cover, acid proof seal
|
|
加料口
Loading hole
|
集成在人孔盖上，三爪，直径250mm
Integrated in manhole cover, 3- claws, diameter 250mm
|
|
泄压阀
Relief valve
|
不锈钢304材质，位于罐体上，通径3英寸，开启压力0.3MPa，不锈钢螺栓连接
Stainless steel 304 material, located on the tank, diameter 3 inches, opening pressure 0.3MPa, stainless steel bolt connection
|
|
爬梯
Ladder
|
不锈钢材质，位于罐体中部左侧，直径38mm，装配式。
Stainless steel, located in the middle left side of the tank, diameter 38mm, prefabricated.
|
|
平台
Walkway
|
不锈钢防滑走台，位于罐顶溢流箱四周，配置矮围栏。
Stainless steel non-slip platform, located around the top of the tank overflow box, equipped with a low fence
|
|
罐口溢流箱
Top overflow box
|
不锈钢304材质。其余按厂家标准与设计。倒凹型，1寸开口，增加槽盖。
Stainless steel 304 material. The rest according to the manufacturer's standard and design. Concave type, 1 inch opening, add slot cover.
|
|
积液软管
Drain hose
|
要求用耐酸浅灰色橡胶软管，连接顶部接兰盘和底部积液箱，要求在O型圈侧面加固定软管锁扣。
It is required to use acid-resistant light gray rubber hose to connect the top connector and the bottom liquid tank. It is required to add a fixed hose lock on the side of the O-ring
|
|
罐 体 下 部 及 侧 面
Tank bottom and side
|
|
爬梯
Ladder
|
同上
Same upper
|
|
卸料口结构
Offloading outlet structure
|
双阀门结构。
Double valve construction
|
|
卸料出口法兰Offloading outlet flange
|
一个4寸不锈钢法兰，标准件，8个18mm孔均布，与原配卸料管道法兰匹配。
A 4 inch stainless steel flange, standard parts, 8 pcs 18mm holes are distributed, matching with the original discharge pipe flange.
|
|
法兰盲板
Blank flange
|
管道出口配置4寸不锈钢阳端接头，法兰装配式。散发1个带把手不锈钢盲板。
Pipe outlet is equipped with 4 inch stainless steel male connector, flange assembly type. Distribute 1 stainless steel blind plate with handle.
|
|
卸料管道
Offloading pipe
|
不锈钢4寸4mm壁厚管道，带弯头，与罐体中央腹部法兰不锈钢螺栓连接。
Stainless steel 4 "4mm wall thickness pipe with elbow, stainless steel bolt connection with tank central belly flange.
|
|
卸料阀
Offloading valve
|
2个4寸球阀；304不锈钢材质，位于罐体左侧中部。
2 4-inch ball valves; 304 stainless steel, located in the left center of the tank.
|
|
快速接头
Quick connector
|
配1套4寸变2.5寸快速接头，该接头可与卸料管实现快速安全连接。阳端接头配防尘盖。
Equipped with a set of 4-inch to 2.5-inch quick connector, the connector can be quickly and safely connected to the discharge pipe. Dust-proof cover is provided for the male connector.
|
|
快速接头阳端
Quick coupling male end
|
与卸料口连接，配有防尘盖。
Connected with discharge port, equipped with dust cover.
|
|
卸料软管
offloading hose
|
无
Non
|
|
管箱
Hose box
|
无
Non
|
|
积液箱，工具箱，石灰箱
Fluid tank, tool box, lime tank
|
车轴前方左右两侧分别设置工具箱和石灰箱，长度约800mm。积液箱设置在中部右侧，右侧开门，内部可以放置塑料桶，积液箱上设置导流阀门。
The tool box and lime box are arranged on the left and right sides of the front axle respectively, with the length of about 800mm. The liquid collection box is arranged on the right side of the middle, the right side door is open, the plastic bucket can be placed inside, and the diversion valve is arranged on the liquid collection box.
|
|
行 走 部 分
Running system
|
|
车架
Chassis
|
Q345材质，需要适合恶劣路况；按照设计。
Q345 material, need to be suitable for harsh road conditions; As designed.
|
|
牵引销
Kingpin
|
90#，装配式 JOST品牌
90#， assembly JOST brand
|
|
罐体与行走连接方式
The connection between tank and running ststem
|
罐体与车架地蹲式结构，螺丝固定连接大梁。罐体地蹲座与车架连接后，前后焊接止滑块。（路况差，注意连接强度）
Tank and frame squat structure, screw fixed connection girder. After the tank floor squat seat is connected to the frame, the front and rear welding stop slider. (Poor road conditions, pay attention to the connection strength)
|
|
悬挂
Suspension
|
机械式板簧悬挂
Mechanical leaf spring suspension
|
|
支架
Bracket
|
厚度大于或等于8mm，加强型
Thickness greater than or equal to 8mm, reinforced type
|
|
采用悬挂类别
Suspension model
|
德式板簧悬挂
Germany model leaf spring suspension
|
|
车轴
Axle
|
13*3（广东富华）；采用加宽制动蹄片，载荷质量：39吨。
13*3 (Guangdong Fuhua); With widened brake shoe, load mass: 39 tons.
|
|
板簧规格
Leaf spring size
|
90x16mm，8片簧
90*16mm 8pc
|
|
轮胎
Tire
|
12R22.5*12三角品牌
12R22.5*12 Triangle brand
|
|
钢圈
Rim
|
9.00*22.5*12
|
|
支腿
Landingear
|
JOST A400联动支腿
JOST A400 Linkage Landingear
|
|
紧急继动阀
Emergency relay valve
|
WABCO 4孔
WABCO brand 4 holes
|
|
制动气室
Brake chamber
|
前一轴单30；后双轴T30/T30
Front axle single 30; Rear twin-axle T30/T30
|
|
备胎架
Spare tire carrier
|
悬链式，装配防盗螺栓，1件。
Catenary, equipped with anti-theft bolts, 1 piece.
|
|
驻车制动
Parking brake
|
装配
With
|
|
灯光
Lights
|
LED制式，线路按照厂标，七芯线制。24V，防水插头与线缆。
LED standard, line according to factory standard, seven-core wire system. 24V, waterproof plug and cable
|
|
线管
Wire
|
整体线束，使用扎带固定线束
whole wires, use cable ties to fix the wire
|
|
尾灯
Rear lights
|
左右每侧设置转向灯、制动/行车灯、雾灯、倒车灯各一，装配防护罩，圆形。
Each side is equipped with a turn signal, brake/running light, fog light, reverse light, equipped with a protective cover, round
|
|
牌照灯
License plate light
|
2件，左右布置。
2pcs， left and right
|
|
边灯
Side light
|
左右各4件
Left and right side each have 4 pcs
|
|
顶部示廓灯
Top lights
|
左右各1个，隐藏式安装线不能裸露。
1 cable on the left and right sides. The hidden installation cable cannot be exposed.
|
|
警示灯
Warning light
|
LED型，与夜间行驶灯连接，位于牌照灯下部。采用红蓝制式（小型方块式LED灯），与行车灯相连。
LED type, connected to the night running light, located under the license plate light. The red and blue standard (small square LED lights) is used to connect with the running lights.
|
|
制动方式
Brake model
|
气压式，双回路，断气制动
Pneumatic, double circuit, air brake
|
|
ABS
|
无/Non
|
|
气 路 系 统
Air-way system
|
|
气路接头
Air-way couplings
|
握手式
Handshaking
|
|
管路种类
Pipe model
|
2套（红黄区分）
2 sets (red and yellow)
|
|
驻车制动
Parking brake
|
装配
Equiped
|
|
附 属 件
Accessory
|
|
灭火器，公斤数
Fire extinguisher
|
尾部两侧，2件，带防护，8公斤级。
Tail sides, 2 pieces, with protection, 8kg.
|
|
独立警示标志板
Independent warning sign board
|
如侧面需要粘贴，采用独立板式，不粘贴于罐体上，反光标识除外。
If the side needs to be pasted, use an independent plate, not pasted on the tank, except for reflective signs.
|
|
水箱
Water tank
|
50升，两个，每侧1只，不锈钢304材质，圆柱体结构，接气路加压，喷涂WATER TANK。
50L, two pcs, 1 on each side, 304 stainless steel, cylinder structure, air path pressure, spray WATER TANK.
|
|
静电接地线圈
Electrostatic ground coil
|
1件10米
One pc 10 meters
|
|
底部出酸口防护杠
Bottom outlet guard bar
|
2.5寸无缝钢管组焊件，装配在罐体上。
2.5-inch seamless steel pipe assembly welds, assembled on the tank.
|
|
反光板
Reflect board
|
红黄斜纹反光板，尺寸1700*200mm;
Red and yellow twill reflect board, size 1700*200mm;
|
|
后保险杠
Rear bumper
|
分为两个独立部件，上部整体内凹式，安装尾灯及牌照灯，下部装反光板与红色三角反光器。
Divided into two independent parts, the upper part of the overall concave, the installation of taillights and license lights, the lower part of the reflector and red triangle reflector.
|
|
危化标识
Danger mark
|
尾部铁质框架内按照要求粘贴其国家危化品标识牌（内容待定）
Attach the national hazardous chemicals identification plate in the tail iron frame as required (content to be determined)
|
|
限速标识
Speed limit sign
|
罐体尾部上喷涂或粘贴限速80KM/H标志（要求醒目）
Spray or paste 80KM/H speed limit sign on tank tail (eye-catching required)
|
|
反光标识
Reflective sign
|
罐体粘贴红白反光贴与黄色危化品反光贴。尾部外圈为红白，内侧为纯黄
The tank is pasted with red and white reflective stickers and yellow reflective stickers of hazardous chemicals. The outer ring of the tail is red and white, and the inner ring is pure yellow
|
|
挡泥板
Mudguard
|
铝合金
Aluminum alloy
|
|
挡泥板胶皮
Mudguard rubber
|
装配，无厂家标志与标识
Equiped
|
|
喷 涂
Painting
|
|
漆前处理
Pre-painting
|
除锈除油，清渣彻底。
Remove rust, oil and slag thoroughly.
|
|
喷砂
Sandblast
|
罐体
Tank body
|
|
底漆
Priming paint
|
2层，喷灰色耐酸防锈漆。
2 layers, spray gray acid and rust resistant paint
|
|
面漆
Top painting
|
2层，白色耐酸
2 layers, white acid resistant
|
|
清漆
Varnish
|
1层
1 layer
|
|
工具箱，积液箱，石灰箱
Fluid tank, tool box, lime tank
|
喷白色面漆；工具箱喷涂：TOOL BOX 石灰箱喷涂：LIME BOX
Spray white finish paint; TOOL BOX spraying: TOOL BOX Spraying: LIME BOX
|
|
行走部分
Running system
|
喷白色面漆（车轴上焊接板簧座部分需要喷涂）
Spray white finish paint (the welded spring seat part of the axle needs to be sprayed)
|
|
其它
Others
|
按照厂标
As the factory standards
|
Contact Now
